|
|
 |
|
Features:
- All
E-Z Kold conversion kits are made with high quality materials
and components, such as welded stainless steel, not stamped, cold
plates
- Pre-chargd
with environmentally friendly R124a refrigerant and factory run
for a minimum of 24 hours to insure proper operation before shipping
- True
12 Volt condenser draws power from your batteries which are charged
when the engine is running or the boat is hooked up to shore power
or alternate power source such as wind or solar.
- Compressor
has brushless (Danfoss BD-35® models) run at low speed when
battery power is reduced and will not run if batteries are low,
never draining the batteries completely.
- The
refrigerant tubing is made of a salt water-resistant alloy.
- The
connectors are quick-connect / quick-disconnect pressurized fittings.
- The
new larger condenser is 25% more efficient than the previous model.
- Water
& air cooled units are designed that the fan always runs whenever
the compressor operates preventing loss of Refrigeration due to
a plugged through hull.
- All
air/water cooled units equipped with an on/off switch for the
water pump, to reduce current draw on cool days or for when a
boat is unattended for extended periods.
- The
pump is self-priming, quiet, will not be harmed if run dry, does
not require a separate through hull and can be mounted above the
water line.
- The
two-plate and box plate systems are configured with the larger
Danfoss BD-50® variable speed compressor.
- Cold
plates are filled with a non-toxic, non-brine eutectic solution.
- We
also supply stainless steel screws for mounting the unit in the
icebox.
- No
water pump required - refrigerant tubes are extended through the
hull and cooled by external water (requires a separate through
hull fitting).
- Our
test results for a 6 cubic foot, well insulated, top-loading box
using a wrap-around box style cooled cold plate at 70° F/21°
C are as follows:
| |
Air
cooled compressor |
24
amps/24 hours |
| |
Keel
cooled compressor |
48
amps/24 hours |
| |
Keel
& air cooled compressor |
21
amps/24 hours |
| |
Air
& Water cooled compressor |
18
amps/24 hours |
|
|
Air
Cooled Conversion Kits
The following are 12 Volt DC conversion
kits designed to convert an existing ice box into a refrigerator
or a freezer or a combinationnrefrigerator/freezer. |
|
|
|
| EK-12EV |
Air
Cooled 12 Volt Evaporator Plate System |
| |
Pre-charged
with environmental-friendly R134a refrigerant |
| |
No
water pump or through-hull required |
| |
Can
be installed in any well ventilated space |
| |
Draws 4.5 amps while running, current consumption varies with
insulation and size of ice box |
| |
Evaporator plate size is determined by the total volume of the
ice box |
| |
Condenser unit size is 12"H x 12"W x 8"D (30.5
x 30.5 x 15.2 cm) |
Back
to Top |
EK-12A
 |
Economic
Air Cooled 12 Volt Cold Plate System |
|
Pre-charged
with environment-friendly R134a refrigerant |
|
Refrigerates
up to 5 cubic feet |
|
Easy
to install as no water pump or through-hull required |
|
Can be installed in any well ventilated space |
|
Runs an average of 3-5 hrs per day to keep the plate fully frozen |
|
Draws 4.5 amps while running, current consumption average 18
amps per 24 hour period, after initial freeze-down. |
|
Cold plate size: 12"H x 5'W x 4"D (30.5 x 12.7 x 10.2
cm) |
|
Condenser unit size: 12"H x 12"W x 8"D (30.5
x 30.5 x 15.2cm) |
Back
to Top |
|
EK-12CPA
 |
Classic
Air Cooled 12 Volt Cold Plate System |
|
Pre-charged
with environment-friendly R134a refrigerant |
|
Refrigerates
up to 5 cubic feet |
|
Easy
to install as no water pump or through-hull required |
|
Can be installed in any well ventilated space |
|
Runs an average of 4-6 hrs per day to keep the cold plate fully
frozen |
|
Draws 6 amps while running, current consumption average 30 amps
per 24 hour period, after initial freeze-down. |
|
Cold plate size: 16"H x 10"W x 2.5"D (40.6 x
25.4 x 6.4 cm) |
|
Condenser unit size: 12"H x 12"W x 8"D (30.5
x 30.5 x 23.3cm) |
Back
to Top |
|
Back
to Top |
|
Back
to Top |
|
Water
& Air Cooled Conversion Kits
Water & Air cooled units are designed
so that the air cooling operates whenever the compressor runs, this
will prevent loss of refrigeration due to a plugged through hull or
other loss of water pressure. On a cool day, you can also choose to
run on air-cooling only, as the current draw is less. |
|
Back
to Top |
|
Back
to Top |
|
Air
Cooled Conversion Kits
Water
& air cooled units are designed so that the air cooling operates
whenever the compressor runs, this will prevent loss of refrigeration
due to a plugged through hull or other loss of water pressure. On
a cool day, you can also choose to run on air-cooling only, as the
current draws less. |
|
Back
to Top |
|
Back
to Top |
|
| Conversion
Kits|Accessories|About
Us|Our Customers|FAQs|Dealers|Marine
Links|Contact Us|Home |
